Gate Installation Guide
How to Install a GATEMATE® Digital Long Throw Gate Lock
Installing a GATEMATE® Digital Long Throw Gate Lock is a straightforward project when you have the correct tools and follow the installation steps carefully. This guide explains what’s included in the kit, how to fit the lock correctly, how to set your access code and how to keep your lock operating smoothly for years to come.
Whether you’re fitting a new garden gate, side gate or pedestrian gate, this guide will help you achieve a professional installation.
In this guide
What You Will Need
Tools you’ll need:
- Drill
- Tape measure
- Pencil
- Spirit level
- Screwdriver or impact driver
- Safety glasses
Included with the lock:
- 3.5mm wood drill bit
- 8mm wood drill bit
- 35mm spade drill bit
- Security Torx driver bit
- Drilling template
Before You Start
- Check the gate is between 45mm and 75mm thick
- Decide the final lock position before drilling
- Make sure the long throw bolt will align correctly with the post/keep
- Check the gate closes freely before fitting the lock
- Set and test your access code before installation
What’s Included
The GATEMATE® Digital Long Throw Lock is supplied as a complete fitting kit, including:
- Digital lock body
- Long throw lock
- Anti-rattle keep
- Two spindle options for different gate thicknesses
- Code change tool
- Springs
- Security machine screws
- Security wood screws
- 3.5mm wood drill bit
- 8mm wood drill bit
- 35mm spade drill bit
- Security Torx driver bit
- Drilling template
Set Your Access Code
Before fitting the lock, set your preferred access code using the supplied code change tool.
- Insert the code change tool into the tumblers for the numbers you want to use.
- Turn the selected tumblers so the U-shaped section faces upwards.
- Tumblers left with the U-shape facing downwards remain un-coded.
- Once the code is set, press the C button and enter your chosen code to test it.
- Check the lock operates correctly before continuing with installation.
Position the Drilling Template
- Peel off the backing and position the supplied drilling template on the gate.
- Make sure the lock is sitting level and at a comfortable operating height.
- Check that the long throw bolt will line up correctly with the gate post and anti-rattle keep.
- Mark all hole positions clearly before removing the template.
- Double-check the alignment before drilling.
Drill the Gate
- Drill the four outer fixing holes using the supplied 8mm wood drill bit.
- Drill the centre spindle hole using the supplied 35mm spade bit.
- Keep the drill straight and level as you work through the gate.
- Accurate drilling is important so the front and rear lock mechanisms line up correctly.
- Take your time and check the holes before fitting the lock.
Fit the Lock
- Place the front digital lock body and rear long throw lock on opposite sides of the gate.
- Make sure the rubber seal/back plate is correctly positioned between the lock and the timber.
- Fit the correct spindle for your gate thickness.
- Insert the spring and make sure the spindle engages properly with the rear locking mechanism.
- Line up the lock with the pre-drilled holes.
- Secure both sides together using the supplied machine screws.
- Tighten evenly and check the lock operates smoothly before moving on.
Fit the Anti-Rattle Keep
- Close the gate and extend the long throw bolt so you can accurately position the keep on the gate post.
- Align the anti-rattle keep so the bolt enters cleanly and fully when the gate is closed.
- Mark the fixing positions.
- Use the supplied 3.5mm wood drill bit to drill pilot holes.
- Do not drill all the way through the gate post.
- Secure the keep using the supplied wood screws.
- Open and close the gate several times to check the bolt moves freely and the gate is held firmly without excessive movement.
Test the Lock
- Close the gate and enter your chosen access code.
- Check that the 65mm long throw bolt moves smoothly into and out of the anti-rattle keep.
- Open and close the gate several times to make sure everything remains correctly aligned.
- Confirm the gate is held firmly when locked and that the anti-rattle keep reduces unwanted movement.
- Check all fixings are secure, but avoid overtightening.
- If the lock feels stiff or does not engage cleanly, re-check the alignment before regular use.
Maintenance
To keep the GATEMATE® Digital Long Throw Lock operating smoothly:
- Lightly brush away any dirt or dust from the lock body and fittings.
- Wipe coated metal parts with a damp cloth and mild household cleaner.
- Avoid abrasive cleaners, strong chemicals and steel wool.
- Keep the stainless steel components clean and dry after cleaning.
- Spray the moving parts and joints with WD-40 approximately every 6 months, or as required.
- Wipe away any excess lubricant after application.
- Periodically check that all fixings remain tight and secure.
Download Instructions
For the full manufacturer fitting instructions, technical specifications, dimensions and maintenance information, download the official GATEMATE® Digital Long Throw Lock Installation Guide & Technical Data Sheet below.
More Help & Advice
Looking for another gate fitting guide?
Guide Details
- Product: GATEMATE® Digital Long Throw Lock
- Gate type: Timber gates
- Gate thickness: 45–75mm
- Lock type: Keyless digital
- Throw: 65mm
- Difficulty: Moderate
Need the lock?
Shop the GATEMATE® Digital Long Throw Gate Lock and everything you need for installation.